【11】laser array

Product name: Laser array

Brief introduction

Players need to across the laser array without touching any of the green lasers and press the end button at the end of this array. Then the lock will be released.

How to reset?

There are 3 options to reset. Users can revise it in 04 folder via TF card.

1) Keep holding the start button for 5 seconds to reset.

2) After triggering successfully, wait for 30 seconds to reset automatically after triggering successfully.

3) Power off the prop and repower to reset.

Product highlights

1. Users can choose the quantity of lasers.

2. Users can revise the audio via TF card in the controller.

3. Users can adjust the reset mode.

4. This prop has anti-cheating system. There are three invisible infrared sensors in the array. All three infrared sensors must sense players when they across the laser array.

Prop list

One controller

Two plastic buttons (Red start button, green end button)

N laser receivers

N laser transmitters

Three infrared sensors

One alarm light

N+1 12V power supplies

Some mirrors

Kindly remind: Users need to provide 12V electromagnet lock.

How to connect?



Installation effect drawing




How to install and test?

1. For laser transmitters and laser receivers, you need to ensure all receivers are fully illuminated by the lasers.

1). If the receivers do not receive the lasers completely, the system will play a sound tip "The sensor did not detect any laser, please check".
2). If all lasers are fully illuminated by lasers, the system will play a sound tip:

The sensor had been in place". It proves that the connection of laser transmitters and receivers is correct.

2.For infrared sensors and reflectors, you should place them at the start position, middle position and the end position of laser array.

Please use your hands to cover three infrared sensors one by one and press the end button, then you will hear the success audio. This proves that connection of infrared sensors and reflectors is correct.

3.For the alarm lamp, please use your hand to cover any one of lasers, then alarm lamp will ring and system will play "Warning! Someone has broken in". This proves that the connection of the alarm lamp is correct.

Audio configuration



FAQ:

Q:   I received 6 lasers, but I only want to use 4 lasers. What should I do?

A: You can use only four lasers, but you need to modify the name of file. If there are 6 lasers, the file name is 006. If you want to use only 4 lasers, please change the file name to 004, and then test the prop.

Q: What is the anti cheating system? Can I not use it?

1. A: Anti cheating system includes three infrared sensors. There are three invisible infrared sensors in the array. All three infrared sensors must sense players when they across the laser array.

You can not use it, or just use one or two, just unplug them from the controller.





Manual to old version


Product name:   Laser array


Brief introduction

There is a four-laser array in the room (Owner can increase or decrease the quantity of the lasers). Players must across the laser array without touching any of the green lasers and press the green button at the end of this array. Then a door will open for players.


Details introduction

1. When get 12v power supply on the controller, but without powering on the transmitters of laser, the system enters standby mode. Then power on the transmitters, the alarm system lights on and let out a warning sound. Then press the red button, the system will be in place.

2. Player will find a four-laser array in the room (Owner can increase or decrease the quantity of the lasers), the electromagnet lock gets closed tightly.

3. When players touch any one of the lasers during the game, there will be alarm audio and alarm light telling them the game has failed, the electromagnet lock is still closed. When they press the green button to open the door, the door can not be opened. They should press the red reset button at the beginning of the array and challenge it again.

4. This prop has anti-cheating mechanism. There are three invisible infrared rays in the array. Adventurers should touch all the three infrared rays to prove they really do across this array instead of some cheatings.

5. When players across the laser array successfully and touch the three infrared rays, the system will play a sound, and press the green button for opening the door, then one lock will release.  


How to reset?

There are 3 options to reset. Room owners can set it by revising the file’s name (001.mp3, 002.mp3 or 003.mp3) from folder 04 in TF card. Please refer to the audio configuration in detail.


Manual reset version:

By default, we put the file’s name as 001.mp3. Keep pressing   the red start button for 5 seconds to reset the prop.


Auto reset version:

Firstly change the file’s name to 002.mp3. Then this prop will reset in 30 seconds automatically after being triggered successfully.


Repower reset version:

Firstly change the file’s name to 003.mp3. Power off the prop and then repower it to reset.

Product highlights

1. Support owner to set the quantity of lasers.3-12

2. Support owner to revise the audio by TF card inside the controller.

3. Room owner can adjust the reset option.

4. This prop has anti-cheating mechanism. There are three invisible infrared rays in the array. Adventurers should touch all the three infrared rays to prove they really do across this array instead of some cheatings.



Prop list

One pcs controller

Two pcs plastic buttons (Red button is for resetting the game,green button is for confirming the game and opening the door)

Four pcs laser receivers

Four pcs laser transmitters

Three pcs infrared sensors

One pcs alarm light

Five pcs 12v power supplies

Kindly remind: Owner needs to provide 12V electromagnet lock.

How to connect with 12V electromagnet lock?

The red wire of the controller should be connected to the red wire of the magnet lock.

The black wire of the controller should be connected to the black wire of the magnet lock.

How to connect with wires?

Configuration

1. First, please open the folder in the TF card.


2. Second, please open the 03 folder.

Here you can configure the number of sensors you want.

If you want to set 5 sensors, you can change the file name into 005.

How to connect this prop?

How to text this prop?

1. After the laser transmitter and laser receiver are connected, ensure that all laser receiver are fully illuminated by the laser, and then the system will have a voice tip.

2. Use your hands to cover the infrared sensor, adjust the infrared sensor, so that it is in the red light is always on the state, and then bring their own infrared mirror to test.

3. When one laser transmitter is unplugged, the system will have a voice tipsomeone broke in the larry, which means that the indicator light is connected correctly.

Audio configuration

share :